Please keep this booklet for future reference.Installer, when you have read these instructions please ensure you leave them with the user.Installation
10Flow Regulators etc.Flow regulators are factory fitted.Study the table on the previous page and decide which flow regulators etc. are required for y
11Installation RequirementsThis fitting needs to be installed in accordance with the following Installation Requirements and Notes (IRN) to ensure the
12Dimensions (mm’s)*Note: The Riser rail wall brackets can be positioned up or down the riser rail (max. 600mm apart) as required. This allows any exi
13SpecificationsSpecifications Inlet connections: 15mm compression, with approximately 150mm between centres.Operating pressure range: Min. 0.1 bar -
14Pack Contents - CAP2 SHUAR C1 Shower valve2 Concealing plate3 Covers x24 Filters x25 Washers x26 Retaining rings x27 White disc8 Green flow
15Pack Contents - SOQ2 SHUAR C1 Shower valve2 Concealing plate3 Covers x24 Filters x25 Washers x26 Retaining rings x27 White disc8 Green flow
16Surface Installation - First FixSurface Mounted Shower ValveBefore InstallationFlush through the pipework to ensure removal of debris. Turn off the
171. Attach shower valve Place the covers (3) over the water supply pipes. Insert the 15mm hot and cold water supply pipes into the inlet connections
18Recessed Installation - First FixRecessed Shower ValveBefore InstallationFlush through the pipework to ensure removal of debris. Turn off the mains
19Recessed Installation - First Fix3. Fit wall outletThere are two methods of fixing the wall outlet depending on the type of wall: a: With rear acce
2ContentsThank you for choosing Bristan, the UK’s leading showers and taps expert. Your Bristan shower valve is a thermostatic mixer incorporating a w
201. Fit concealing plateNote: The concealing plate (2) can be used as a template by drawing around the plate and measuring in by 15mm to give suffici
21Installation - Riser Rail1. Mark the position Position the assembled riser rail on the wall, bearing in mind the different heights of people likely
22Installation - Riser Rail cont.3.Insert rail clamps Insert the rail clamps into both wall brackets. 4. Insert riser railPush the riser rail up throu
23Installation - Riser Rail cont.Attaching the Shower hose7. Connect shower hose to shower valve / wall outletScrew the shower hose (ribbed nut end) o
24CHCHOperationOn/Off and Temperature ControlTurn the lever anti-clockwise to turn on and increase temperature.Turn the lever clockwise to decrease te
25CommissioningCommissioning notes for Thermostatic Mixing Valves The first step in commissioning a thermostatic mixing valve is to check the followin
26MaintenanceGeneral Cleaning Your fitting has a high quality finish and should be treated with care to preserve the visible surfaces. All surfaces wi
27Maintenance - cont. Adjusting the Temperature The shower valve has been factory set with equal (balanced) hot and cold water supply pressures with t
28LULLLLCHCWSYSALDCFHRCMOXBSGLSNSPBATAEXPLTQTRDTBHSOPOPOGUBNTNRHRGSL HPALCTMEDAKTSGMKNNPENRIPCBCOLEWRTFWVWSSTSKDEBCVDYHGLNSDNYOHGNECALADLDHPRLWNBLW
29Symptom Cause RemedyNo flow or low flow rate and / or varying temperatures.Check showerhead, hose and filters for any blockage.Clean as necessary,
3Important Safety Information• Please read these instructions thoroughly and retain for future use. • All products manufactured and supplied by Brista
30Symptom Cause RemedyMaximum water temperature too hot or cold.Maximum water temperature set incorrectly.Reset maximum water temperature. Refer to ‘
31Bristan offers solid guarantees to provide you with complete peace of mind.Taps and Mixers 5 year parts and 1 year labour*. Gold, painted and speci
32• Components that are subject to general wear and tear such as filters, seals, ‘O’ rings and washers etc.• Damage caused by faulty installation• Dam
33Notes Please use this space to add any notes you or your installer may have regarding the plumbing system/installation of this product.
35Notes
36Bristan Group Ltd. Birch Coppice Business ParkDordonTamworthStaffordshireB78 1SG Web: www.bristan.comEmail: [email protected] Masco CompanyPart N
4General InformationOperating pressure range: Minimum 0.1 bar, Maximum 5.0 bar. Maximum static pressure: 10.0 bar.This product has been tested to the
5Product featuresRecommended UsageDomesticHeavy CommercialLight CommercialHealth Care1. On/Off and Temperature ControlTurn lever anti-clockwise to tur
6Installation RequirementsThis shower valve must be installed in compliance with current water regulations. If you have any doubts about the water reg
7Installation RequirementsUnvented SystemInstantaneous Water HeaterPumped Systemcold mains supplycold mains supplycold mains supplyPumped System (with
8Installation RequirementsConditions of use for Type 2 (Thermostatic mixer) valvesHigh Pressure Low Pressure Maximum Static Pressure (Bar) 10 10Flow
9Installation RequirementsSupply System Flow RegulatorCold Supply Hot Supply Cold Hot Comments0.1 to 1.0 bar 0.1 to 1.0 bar No NoMaximum pressure loss
Kommentare zu diesen Handbüchern